MENU
Important announcement – End of support information for Graphtec Pro Studio / Plus, Cutting Master 4 MORE
  1. HOME
  2. Download
  3. Firmware for CE6000 series download

Firmware for CE6000 series download

Software License Agreement

It is required to review the following license agreement before the software is downloaded. We will be deemed that the customer has to agree to the terms and conditions of the license agreement when the software had been downloaded by the customer. Please note that it is not possible to download or use the software if the customer does not agree to it.

GRAPHTEC SOFTWARE LICENSE AGREEMENT (GSLA)

Downloading Files

Ver.2.70 (Latest version)

Date of updated16 Feb, 2022
Supported ProductsCE6000-40 / CE6000-60 / CE6000-120
Supported OSWindows 11 / 10
Downloading filesSoftwareCE6000_FU(v270).zip (3,277KB)
  • The plotter driver must be installed for use.
  • Please read the update instructions carefully before completing the firmware update.
    If the update is not performed according to the procedure, the cutting plotter may not start.

Revision History

Ver.2.70

  1. Fixed the problem that a beeping sound would continue to sound when moving a tool using key.
  2. Fixed the problem that the key might become unresponsive when pressing the PAUSE key while reading the multiple registration marks.

Ver.2.61

  1. Increased the cutting speed of straight lines over multiple segments in the data of segmented area registration marks.
  2. Fixed the problem that caused extra feed after finishing cutting when cutting data with matrix registration marks and the media feed is being set.
  3. Fixed the problem that a scanning error occurs when scanning black and white inverted segment area registration marks TYPE 1.
  4. Fixed the problem that an error occurs when exiting from MENU after canceling the data which has rotated in the driver setting by pressing the PAUSE key and re-sending the cutting data while MENU is displayed.
  5. Fixed the problem that the only first vector was not cut by the set cutting pressure in the following combinations.
    ・Turn on the panel cutting.
    ・The cut data contains a command to change the CONDITION No.

Ver.2.50

  1. Supported Auto Sheet Feeder Unit F-MARK.

Ver.2.40

  1. Fixed the problem that the settings were not reflected when setting the cut line pattern from the software (CE6000-120 only).
  2. Fixed the problem that the plotter starts scanning from the wrong position from the third data doing media switch copy after sending the data with registration marks and setting the command to GP-GL.

Ver.2.20

  1. Fixed the problem that cutting condition settings were not saved when sending a cut job from Graphtec Studio or Cutting Master 3 and copying the data on the main unit after the operation was completed.
  2. Fixed the problem that when sending a cut job that includes registration marks from Graphtec Studio or Cutting Master 3 and copying the data on the main unit after the operation is completed, the cut job could not be canceled even if the plotter failed to read the marks and the media was cut based on the origin point.

Ver.2.10

  1. Fixed the problem that sometimes the scanning error occurs when feeding a media sticked on a cutting paper with the automatic registration mark scan.
  2. Fixed the problem that the command would be judged as HP-GL and cannot be able to draw when connecting Graphtec Studio or Cutting Master 3 to RS-232C and the command setting is “AUTO”.
  3. Fixed the problem that the origin point shifts when pressing the ORIGIN key multiple times even the user has not moved the tool carriage.

Ver.2.00

  1. Fixed the problem that the new origin point was placed away from the set position when the panel cutting is ON and the [Feed Media] of driver setting.
  2. Improved the accuracy of registration mark scan.
  3. Fixed the problem that the display switches to the operation stop screen when pressing the PAUSE key while waiting for ENTER of the HP-GL NR command.
  4. Fixed the problem that an X position error would easily occur when pulling out roll media.

Ver.1.90

  1. Supported unique characters such as numbers with circles in Kanji fonts.
  2. Fixed the problem that the media selection screen would freeze when the set lever was moved before pressing ENTER key to switch the tool 1 and 2.
  3. Fixed the problem that the cutting plotter freezes when the media was set in ROLL-1 and press PAUSE key after feeding the media.
  4. Fixed the problem that the status of Cutting Master 3 remained “Waiting for panel input” when the command was switched from GP-GL to Auto by the key operation of the main unit while Cutting Master 3 was connected via USB.
  5. Fixed the problem in which the position of the data with the registration mark was shifted after the registration mark was corrected when the data was copied in array and the distance from the origin point was more than about 1.5 m.
  6. Fixed the problem in Cutting Master 3 that when the cutting plotter is set to “Auto cut when not in use” and the data with registration mark is copied by the main unit, “Error in reading the registration mark” is displayed during the operation of reading the registration mark when retrying to read the registration mark after failing to read the registration mark.

Ver.1.80

  1. Fixed the problem of the maximum plotting range when the push roller sensor was disabled and the problem in the maximum plotting range when expanding.
  2. Fixed the problem in which the timing of automatic prefeeding differed depending on the distance correction when the split connection is turned on and automatic prefeeding is turned on.

Ver.1.70

  1. Changed the setting that the pen can be moved by the POSITION key while stopped by pressing the PAUSE / MENU key during plotting.
  2. Fixed the problem that the origin key did not work in pinch roller ignore mode.

Ver.1.60

  1. Changed the setting that the origin point can be set even when split connection is turned on.
  2. Corrected of LCD display messages (German, French, Spanish, Portugues).

Ver.1.50

  1. Fixed the problem that caused a “confirming push roller point” error even when the push roller is on the grid.

Ver.1.40

  1. Corrected the phrases of LCD display messages (Russian, Chinese, Korean).

Ver.1.00

  1. First edition