MENU
Important announcement – End of support information for Graphtec Pro Studio / Plus, Cutting Master 4 MORE
  1. HOME
  2. Download
  3. Firmware for FC9000 series download

Firmware for FC9000 series download

Software License Agreement

It is required to review the following license agreement before the software is downloaded. We will be deemed that the customer has to agree to the terms and conditions of the license agreement when the software had been downloaded by the customer. Please note that it is not possible to download or use the software if the customer does not agree to it.

GRAPHTEC SOFTWARE LICENSE AGREEMENT (GSLA)

Downloading Files

Ver.1.39 (Latest version)

Date of updated27 Dec, 2023
Supported ProductsFC9000-75 / FC9000-100 / FC9000-140 / FC9000-160
Supported OSWindows 11 / 10
Downloading filesSoftwareFC9000_FU(v139).zip (3,425KB)
  • The plotter driver is required to be installed for use.
  • Please update the firmware according to the instructions to start cutting plotter properly.

Revision History

Ver.1.39

  1. Fixed the problem that crosscut starts when canceling while drawing USB flash memory data.
  2. Fixed the problem with length accuracy of the first piece of repeat crosscut.
  3. Revised the window message appears when saving the settings at [Remote Panel Utility].

Ver.1.38

  1. Repeat crosscut is supported.
  2. Offline setting function of [Remote Panel Utility] is supported. *Do not use flat type setting files.
  3. Fixed the problem that the setting window of [Remote Panel Utility] does not appear.
  4. Fixed the problem that the media drops when using Matrix copy and crosscut between registration marks in combination.

Ver.1.36

  1. Removed the cross-cut check function which was added in V1.35. V1.36 has a same content as V1.34.

Ver.1.34

  1. Fixed the problem that the tool cartridge hit the side in operation after cross-cutting, which caused position error.

Ver.1.33

  1. Added items to service LOG.
  2. Added the distance traveled per speed/acceleration setting and the number of crosscuts to the service LOG.
    Note: The tool Cutting Service Log (v1.5.0.0) or later is required to obtain the logs with the added items.

Ver.1.32

  1. Fixed the problem that “Error Realign Push Rollers” sometimes occurred even though the push roller was set on the grit roller.

Ver.1.31

  1. The data was sometimes missing in the beginning of the part when sending crosscut command by using TC35 command continuously.

Ver.1.29

  1. Fixed the problem that when using the Segment Area Registration Mark, a line segment that was not actually part of the data was drawn when crossing the first segment in some data.
  2. As a countermeasure against moving coil damage, a tool position error is made when the following occurred.
    – When the tool position is lowered below the home position during the pen down check at power-on.
    – When a current value of 500mA is loaded for more than 5 seconds by PWM control.

Ver.1.28

  1. Fixed the problem that when reloading the media which was loaded once and selecting “CONTINUE” from the Select menu, the origin point when the media was first set was not correctly taken over.

Ver.1.27

Fixed the following 4 problems that occur when using Automatic Take-up Roller (OPH-A43/44).

  1. Take-up operation was not performed in panel cutting.
  2. If the gap between the central registration marks was too long in the segment area adjustment, the take-up operation was not performed even though the media was slacking.
  3. When TAKE-UP is ON in the MEDIA SETTING menu and press the HOME key in READY status after plotting, the media is over-tensioned and abnormal noise occurs then cannot move to the original point.
  4. After panel cutting, there was a case that the registration marks could not be read when duplicate the cutting data with the registration marks using COPY key.

Ver.1.26

  1. Fixed the problem that when sending cutting data with tool exchange while Tool Sort and Auto Paneling were turned on, incorrect condition numbers could be displayed.
  2. Fixed the problem that when sending cutting data with tool exchange while Tool Sort and Auto Paneling were turned on, extra lines were sometimes cut on the second sheet.

Ver.1.25

  1. Fixed the problem that when the tool sort was selected, plotting data with multiple registration marks occurred in a scanning error at the second mark.

Ver.1.24

  1. When the “AUTO” was selected in the initial blade control mode selectable function, the pen block moved and hit to the left end in case the specific data was output.

Ver.1.21

Fixed problems

  1. When the rear registration mark is detecting for X/Y segment Registration mark, there is extra movement.
  2. When the small size of 4-point Registration mark is detecting, the detecting error was displayed.
  3. When the first registration mark of Y position is far from the origin point for the X/Y segment registration mark, the extra line was cut.
  4. When the data of multi-registration mark is cutting, the media did not drop down after the crosscut performed.
  5. When the last data of multi-registration mark cutting was finished with the Copy mode, the media dropped to the rear.

Ver.1.20

  1. Fixed the problem that when the roll mode barcode print media was loaded as reverse direction while the XY segment registration mark was performed, the cutting position was shifted about 0.3 mm to 0.4 mm.
  2. Fixed the problem that when the USB memory of data was cutting, the cross cutting was not performed with the specified timeout setting.
  3. Fixed the problem that the blade consumption alarm of beep was not working for the group 8.

Ver.1.10

  1. The mode 4 of registration mark scanning was added to detect the high reflective media.
  2. The maximum cutting length for perforation pattern was changed from the 100mm to the 500 mm.
  3. Modifies to select the external clock of CPU to the full speed mode of USB.

Ver.1.04

  1. The push out operation of crosscut was improved. When the feeding distance is shorter than 380 mm, the finished media feeds the 200 mm to push out, and them the fan is turned off.
  2. The margin for the push roller detection was added to detect the push roller position correctly.
  3. The maximum alarm distance for Blade wear alarm setup was changed from the 5 km to the 100 km.

Ver.1.03

  1. Fixed a problem that tool holder would move in the position without the tool (low position) if you operated it once without a tool in the tool holder, and after checking the operation, inserted the tool in the tool holder and operated it.