MENU
Important announcement – End of support information for Graphtec Pro Studio / Plus, Cutting Master 4 MORE
  1. HOME
  2. Download
  3. Firmware for FCX4000 series download

Firmware for FCX4000 series download

Software License Agreement

It is required to review the following license agreement before the software is downloaded. We will be deemed that the customer has to agree to the terms and conditions of the license agreement when the software had been downloaded by the customer. Please note that it is not possible to download or use the software if the customer does not agree to it.

GRAPHTEC SOFTWARE LICENSE AGREEMENT (GSLA)

Downloading Files

Ver.3.40 (Latest version)

Date of updated20 Nov, 2024
Supported ProductsFCX4000-50ES / FCX4000-60ES
Supported OSWindows 11 / 10
Downloading filesSoftwareFCX4000_FU(v340).zip (3,751KB)
  • The plotter driver must be installed for use.
  • Please read the update instructions carefully before completing the firmware update.
    If the update is not performed according to the procedure, the cutting plotter may not start.

Revision History

Ver.3.40

  1. Fixed the problem that the tool goes back to original position after moving it when [Advance after Plot] is activated.
  2. Fixed the problem that the message window was not displayed properly when editing settings of Remote Panel Utility.

Ver.3.30

  1. Fixed the problem that cutting data for two consecutive outputs of USB memory files could be connected when copying is executed.

Ver.3.20

  1. Offline setting function of [Remote Panel Utility] is supported.
    *Do not use grid type setting files.
    *Do not turn off the power immediately after executing the cut condition setting from the USB memory. Wait about 3 seconds before the next operation.

Ver.3.10

  1. Changed the speed of the tool carriage to be set 15/sec when pressing [PAUSE/MENU] key and [COND/TEST] key to move it away.
  2. Corrected the name of the creasing tool in the line [2 TOOL] of the Condition Screen.

Ver.3.00

  1. Fixed the problem that the cutting order error occurs depending on the type of cutting blade being set when using the REVERSE REGISTRATION MARK.

Ver.2.90

  1. Improved the initialization operation when setting Initial Blade Angle Position to “Y OUTSIDE” not to damage the media.

Ver.2.80

  1. Fixed the problem that the CONDITION No. does not be reflected when changing it with a command from the CONDITION No. selection screen.

Ver.2.70

  1. Fixed the problem that the CONDITION No. does not be reflected when changing it from the MENU.

Ver.2.50

  1. Changed the control method of the tools to improve the image resolution.
  2. Fixed the problem that the beeping sound continue when moving the tool carriage with position keys.

Ver.2.40

  1. Fixed the problem that an error occurs to the cutline when using the segment area registration marks depending on data.

Ver.2.20

  1. Fixed the problem that the height goes low when setting TOOK UP HEIGHT to HIGH.
  2. Improved some movements when setting SCAN START POSITION to CURRENT POSITION.
  3. Fixed the problem that the registration mark scan fails when using Multiple registration marks with TOOL Sort is ON.。

Ver.2.10

  1. Improve the image resolution when using the cutter CB09U.

Ver.2.00

  1. Improved the initialization operation when setting Initial Blade Angle Position to “XY OUTSIDE”.

Ver.1.90

  1. Fixed the problem that a position error occurs if receiving a command while the motor is moving and the [COMMAND] setting is [AUTO].
  2. Expanded the maximum amount of the BLADE WEAR ALARM SETUP to 100km.

Ver.1.70

  1. Fixed the problem that the tool carriage moves at the lower position, when moving it after operating a test without the tool installed.

Ver.1.60

  1. Added [TOOL DOWN SPEED] menu to change the speed of pen down.
  2. Changed the name of the menu item [TOOL UP SPEED] to [MOVING SPEED].
  3. Updated the USERS MANUAL (PDF).

Ver.1.50

  1. Fixed the problem that the ORIGIN POINT command does not be reflected when copying.

Ver.1.40

  1. Changed the direction of the blade tip revision to be the same as the first cutting line in order to improve the image resolution.
  2. Changed the method of terminating arcs and curves in order to improve the image resolution.
  3. Fixed the problems that the cutting plotter hangs when operating followings.
    1) Cut Multiple registration marks.
    2) Press [PAUSE] key while scanning the second registration mark.
    3) Cause a scan error.
    4) Cancel.

Ver.1.20

  1. Changed the operation when lowering the registration mark sensor.
  2. Fixed to wait for the ENTER key being pressed at the HOME position when changing pen tools and TOOL SELECT PAUSE SETTING is set to ENABLED.